Are HID Ballasts Universal?

Is 35w HID better than 55w?

It allows HID bulbs and ballasts to operate independently of the vehicle’s original wiring system and can provide a power source that is more consistent.

55W ballasts should only be installed alongside 55W bulbs since you run the risk of running down 35W ballasts much faster if they’re powered by a higher power source..

How long should a ballast last?

about 20 yearsThe ballast takes in electricity and then regulates current to the bulbs. A typical ballast will generally last about 20 years, but cold environments and bad bulbs can decrease this lifespan significantly. You can get a new ballast at a hardware store or home center and install it in about 10 minutes.

Why are my HID lights different colors?

New HID bulbs have a color temperature of approximately 4150°K. As a bulb is used, the color shifts to the “bluer” color range of 4,300°K. When first installed, the new bulb will cast a light that is a bit more yellow/white than blue/white. … Be prepared for a difference in headlight colors during this break-in period.

Which is brighter 6000k or 8000k?

While it might seem a bit odd, the 6000K LED headlights are brighter than the 8000K headlights – and there’s science to back this distinction. Light intensity is measured in Kelvin units, which are abbreviated to K.

Can I use any ballast with any HID bulb?

Technically speaking you can use any HID bulb with any HID ballast as long as you can connect them.

Are HID kits universal?

HID kits tend to be universal too, which means that they should fit any car or vehicle that currently houses standard halogen headlights. So if you’re looking for a brighter drive, with more energy efficient, longer-lasting headlights, there’s absolutely no reason not to upgrade your vehicle.

How many years do HID bulbs last?

An HID bulb should last anywhere from 2,000 to 3,000 hours. That’s up to six times longer than the shortest-lived halogen bulbs. With an HID bulb, you should get several years’ worth of use before the bulb needs to be replaced.

Can I just put HID bulbs in my car?

‘ The short answer is yes, but you’ll need to use an HID Conversion Kit. Xenon HIDs won’t fit into spaces that are designed for halogen bulbs, and vice versa. Keep on reading to get the lowdown on fitting xenon bulbs into a halogen car…

How much does it cost to get HID headlights installed?

Cost to replace a headlight Enlow says the average cost he pays for a halogen bulb for a customer is $15 to $20. He charges $50 per headlight for installation. According to aftermarket parts retailer AutoZone, the average cost of a halogen bulb is about $15 to $20, while HID bulbs typically cost $100 or more.

Can you use HID bulbs without ballast?

Without HID ballasts, the bulbs won’t function. It is essential that you buy a HID conversion kit that includes HID bulbs, ballasts, mounting elements, wiring, etc.

Can a HID ballast be repaired?

If you are wondering why your HID lamp isn’t working, it could be due to the HID ballast needing replacement. It may spark but not fully light up. Fortunately, there is a way to repair it. … First, check for the proper voltage and amps for the HID ballast you are using.

What is better HID or LED?

LEDs are ideal as they are brighter but do not produce the same glare that HIDs are responsible for. LEDs are compact and energy efficient. Unlike the HID, LED headlights provide instant light when turned on. … Like the HID headlight, they shine very brightly and are often mistaken as hi-beams as well.

How do I know if my HID ballast is bad?

One probe of the multimeter should touch the hot wire connections, while the other touches the neutral wire connections. If the ballast is good, an analog multimeter has a needle that will sweep to the right across the measuring scale. If the ballast is bad, then the needle won’t move.

Can you use 55w HID 35w ballast?

You can use 55w ballasts with standard 35w bulbs, but the life of the bulb will be shortened a bit, and their color will Wash Out a bit. … No, HID bulbs and ballasts do not need to be bi-xenon specific when used in a projector based system to be capable of producing light for low and high beam modes.