- How do I get my volume to work on my AT&T Remote?
- Why is my uverse WIFI not working?
- How do I get my DVR recordings back?
- How do I fix my receiver?
- How do you reprogram a TV remote?
- Why is my Uverse DVR not working?
- How can I boost my uverse wireless signal?
- How do I connect my router to my AT&T modem?
- How do I reset my U verse wireless receiver?
- How do you restart a receiver?
- Why is my ATT Uverse remote not working?
- How do I fix my SSID problem?
- Why is my fiber Internet not working?
- Why is my broadband not working?
- How do I connect my uverse wireless receiver?
- How do I program my ATT Uverse remote to the receiver?
- Why does my uverse keep freezing?
- How do you fix a TV that says no signal?
- How do I get another uverse box?
- How do I fix my uverse connection?
- How do I reboot my directv receiver?
How do I get my volume to work on my AT&T Remote?
If you want the TV volume to be controlled by the volume keys, regardless of what mode the remote is in, do this:Press and hold the AT&T button on the remote.Press the OK button and release it and the AT&T button at the same time.
Press the TV button.
Press the AT&T button..
Why is my uverse WIFI not working?
Power cycle (reboot) your AT&T gateway – Unplug the gateway from the power outlet in the wall and wait two minutes before plugging it back in. … Check your cables – Verify that all physical connections to your AT&T gateway and computer are in place (e.g., phone line, power cords, ethernet cables).
How do I get my DVR recordings back?
Recover recordings without deleting your programsUnplug the DVR power cord from the wall or back of the box and wait 10 seconds.Plug the DVR back in.Wait for 3 white dots to appear on the screen.Repeat the first 3 steps 2 more times.Keep the DVR plugged in.
How do I fix my receiver?
How to Fix Stereo ReceiversLook over the cable connections running into the receiver. Make sure the cables are completely inserted into both the receiver and any connected hardware. … Look over the fuses on the back of the receiver. … Open up the CD tray of the stereo receiver. … Wipe off the air intake vents on the side of the stereo receiver.
How do you reprogram a TV remote?
How to Connect a Remote to a TVHold down the program button on the remote control for 3 seconds. This button mighty be displayed on the remote as “PRG.” When you have done this, the LED light on the remote control will turn on. … Press the “TV” button on the remote control to let the remote know it will be syncing with a TV.
Why is my Uverse DVR not working?
Try these quick tips: Restart your U-verse TV receiver (DVR) by holding down the POWER button for 10 seconds, then press it again to restart. (This takes 5-8 minutes and impacts any DVR recordings in progress.) Press the Recorded TV button on your remote if your recorded program is frozen or missing.
How can I boost my uverse wireless signal?
Weak signal on Uverse wireless tv receiver – options to increase signal move WAP closer to the receiver by running longer Ethernet cord from it. move your wireless TV receiver closer. move equipment out into the open/make sure there are no obstructions or interference near equipment.More items…•
How do I connect my router to my AT&T modem?
Turn the power to your computer and DSL modem OFF, and disconnect the Ethernet cable from your computer. Connect the Ethernet port of your DSL modem to the WAN or Internet port on your router using an Ethernet cable. Turn the power to both your DSL modem and your router ON. Turn the power to your computer ON.
How do I reset my U verse wireless receiver?
Restart your U-verse receiver(s) by holding down the POWER button for ten seconds, then pressing again to restart. (This takes 5-8 minutes and will impact any DVR recordings in progress.) Restart your gateway by removing the power cord for two minutes then plugging it back in (will interrupt AT&T Service).
How do you restart a receiver?
Restart your receiver or troubleshoot specific issues Many receiver problems can be fixed by restarting your receiver. To do this, press and hold the Power button for 10 seconds. This takes 5-8 minutes and will impact any DVR recordings in progress.
Why is my ATT Uverse remote not working?
Check the batteries – When you press the AT&T button located at the top of the remote control, the button should shine brightly. If the button does not shine, change the batteries. … Restart your receiver – Hold down the POWER button for 10 seconds then press it again to restart.
How do I fix my SSID problem?
Check your firewall settings; problems here are very common. You may have a blocked port. For best results, always change your SSID, and disable SSID broadcast if possible. Change the security setting using a complex key and WPA security at a minimum.
Why is my fiber Internet not working?
The most common causes of fiber optic malfunctions Insufficient transmitting power. Excessive signal loss due to a cable span that’s too long. Excessive signal loss due to a contaminated connector. Excessive signal loss due to faulty splices or connectors.
Why is my broadband not working?
Make sure that the power cable is plugged firmly into the Hub. Broadband customers using the Openreach modem, check if it’s turned on. Then check that the Ethernet cables are connected. … If you can it’s a really good idea to try connecting via an Ethernet cable to see if you still have a lost broadband connection.
How do I connect my uverse wireless receiver?
Press the OK button on the front of the wireless TV receiver. Wait two minutes for the receiver and WAP to pair. After two minutes, the Link light on the front of the wireless TV receiver should be solid green. Following a successful pairing, unplug the wireless TV receiver and reconnect it at the desired location.
How do I program my ATT Uverse remote to the receiver?
Here’s all you need to do:With your TV on, use your U-verse TV remote and press Menu.Select Help > Information > Remote Control Setup.Next, select your remote control from the TV onscreen list. Refer to your specific remote for TV/device setup options.Select Top Ten Brand Setup, Automatic Code, or Manual Setup.
Why does my uverse keep freezing?
Check the connections on the rear of the U-Verse receiver and your TV. Loose connections can disrupt service and freeze the image on the TV. Check the coaxial connection to the TV IN jack on the rear of the receiver as well as the audio visual connection between the TV and the receiver.
How do you fix a TV that says no signal?
2 – If you have your TV on the correct INPUT or SOURCE and you still see NO SIGNAL… -Remove or unplug the power cable from the Cable TV or SAT set top box. … -Plug the power cable back into your Cable or SAT set top box. -Give it some time for the Cable or SAT box to power up, get the signal, and initialize.
How do I get another uverse box?
Replace your wireless receiverUnplug the existing receiver from the electrical outlet.Remove the power cord.If possible, stack the new receiver on top of the receiver to be replaced.Carefully remove one connection at a time from the receiver to be replaced and reconnect to the new receiver.More items…
How do I fix my uverse connection?
You should be able to fix the issue by unplugging your receiver and waiting at least 5 minutes. After you’ve plugged it back on, restart the receiver and the problem should be resolved. If it’s still not working, try troubleshooting your issue through U-Verse’s TV support.
How do I reboot my directv receiver?
Unplug your receiver’s power cord from the electrical outlet, wait 15 seconds, and plug it back in. Press the Power button on the front panel of your receiver. Wait for your receiver to reboot.